希捷320G 7200.11数据丢失，求助。

阿哈哈 · 发表于 2008-8-19 09:59:32

其实这毛病并不能说就是你的误操作造成的，希捷近年来太不招人喜欢了。
从之前的2.5 apple用硬盘的问题闹得沸沸扬扬，到现在3.5的11系列又老毛病不断。

fayesong · 发表于 2008-8-19 10:00:27

再次请大家给我点意见

由于我盘上的文件，特别是小孩的，对于本人及至全家人来说实在是太重要了。现在盘交给一家数据恢复公司在搞。昨天一早交过去的，到

下班时间都还没有任何实至上的进展。

实在害怕中间出现什么问题造成数据无法恢复。

现在我是继续让他们研究呢？还是自己拿回来等待相关软件支持了，从而有一个完整的解决方案？

csdn · 发表于 2008-8-19 10:00:34

在国外希捷7200.11对指令质疑改变了，这点和我测试的结果是相同的，好盘都不接受指令信息，来自国外的测试原文如下：

Set parameters at 38400,n,8,1. Issue CTRL-Z command afterward to enter command mode. Then type CTRL-L to output firmware parameters. However, the commands have definitely changed from previous models so there is not much more you can do after this aside from playing around with some additional CTRL-letter commands.

I have two models of 7200.11 that do not respond to CTRL-Z on serial terminal although both drives are functioning normally in all other respects. With these drives there is no "sign-on" message at power-on. The drive models in question are ST3500320AS and ST3750330AS.

However, I have another 7200.11 model, a ST3320613AS, that does report a sign-on message and will allow access to the serial diags with CTRL-Z, although as others have said, the commands are different.

Have you also seen this problem, or do you think that my two drives are bad or perhaps the serial terminal is disabled somehow on these two models?

fayesong · 发表于 2008-8-19 10:02:29

原帖由 阿哈哈 于 2008-8-19 09:59 发表

 登录/注册后可看大图

其实这毛病并不能说就是你的误操作造成的，希捷近年来太不招人喜欢了。
从之前的2.5 apple用硬盘的问题闹得沸沸扬扬，到现在3.5的11系列又老毛病不断。

谢谢您，现在我的心情无法形容，总之非常焦急。。再看到兄弟们热情的帮助，出谋划策，让我得到了很大宽慰，真的很感谢！

硬盘菜鸟2008 · 发表于 2008-8-19 10:09:27

其实很简单，7200.11的盘,波特率更高，PCI没有办法支持

阿哈哈 · 发表于 2008-8-19 10:17:53

这文章我也看过了，可惜找不到解决方法啊。不论指令或者软件或者什么的，能修好才是关键。就数据恢复而言，更注重结果。可关键就在于目前没有结果。。。呵呵

楼主想试验交给专业公司到也没什么，不过机会应该不大吧。*个人看法

csdn · 发表于 2008-8-19 10:20:15

阿^_^看看如下信息：

ST3500320AS - 7200.11
BaudRate=38400 [38400,No,8,1]
Online commands:
Ctrl+A, Ctrl+L -> (PCB+HDA or PCB only!)
Ctrl+U ... -> (PCB+HDA)

ROM is 512kB, and many informations are stored in ROM...
Mikippp

RequestResumeSaveSmartFrame
F3 T> [Ctrl+Z]

F3 T> [Ctrl+A]
Package Version: MS0100.SDD2.AD090B.SD25 , Package P/N: 100504083, Package Builder ID: 3K,
Package Build Date: 01/16/2008, Package Build Time: 16:26:59, Package CFW Version: MS01.SDD2.00052452.3K00,
Package SFW1 Version: B000, Package SFW2 Version: C0FE, Package SFW3 Version: C0FA, Package SFW4 Version: ----
Controller FW Rev: 01161626, CustomerRel: SD25, Changelist: 00052452, ProdType: MS01.SDD2, Date: 01/16/2008, Time: 162659, UserId: 00000761
Servo FW Rev: C0FE
RAP Format Rev: 0092, Contents Rev: 15 05 10 06

F3 T> [Ctrl+L]
TetonST 2.0 SATA Moose Gen 3.0 (RAP fmt 10 ) w/sdff (RV )
...
...
...

F3 T> [.]
Current R/W User LBA 00000000 LLL CHS 000000.0.0000 PLP CHS 000000.0.0000
R/W Status 1 R/W Error 00000080 Ready

F3 T> [;]
This command is no longer supported.
Use the Online Control-L command instead.